Skip to content
Positive Contractors · Blog
Go back

Case Study: HIU and Underfloor Heating Repair in Loughton

This job was a heating call-out to a flat in Loughton, Essex (IG10). The flat has wet underfloor heating, fed by a heat interface unit (HIU) rather than its own boiler. It was booked in as an HIU actuator repair because the underfloor heating was not working properly. Here is what our engineer found, what we did, and what you can check yourself if your own underfloor heating goes cold.

How heating works in a flat like this

Many newer flats in Loughton and across Essex don’t have a boiler. Instead, hot water from a shared plant room is piped to each flat, and an HIU in a cupboard passes that heat over to the flat’s own heating and hot water. The HIU’s heating side is a sealed system, a bit like a combi boiler’s, and it needs the right water pressure to push water round the pipes.

From the HIU, the heating water goes to an underfloor heating manifold. This is the row of valves you can see in the photos below. Each loop of pipe under the floor (a “zone” or circuit) has:

  • a flow meter on the top rail, the small clear tube with a red marker, which shows water is moving through that loop;
  • an actuator on the bottom rail, the white cap, which opens and closes the loop when the room thermostat calls for heat.

Underfloor heating manifold in a Loughton flat, showing six flow meters with red markers on the top rail

What we found and what we did

Because the job was booked as an actuator fault, it would have been easy to start replacing parts on the manifold. Our engineer checked the system first.

He repressurised the HIU, bringing the sealed heating side back up so water could circulate properly. He then tested every underfloor heating zone in turn. All zones heated up correctly, and the system was left fully operational, with no further issues found at the time of the visit.

Underfloor heating manifold with the actuators on the lower rail, after the HIU was repressurised and all zones tested

Why it matters

When underfloor heating goes cold, the actuators often get the blame, because they are the part that opens each zone. But if the HIU’s heating side has lost pressure, no zone can get enough flow, however well the actuators work. Checking pressure and flow first means:

  • no parts changed that didn’t need changing;
  • the fault is fixed at its cause, not just where it shows up;
  • every zone is tested before we leave, so you know the whole floor works, not just one room.

Our recommendation: an HIU service every September

Our engineer’s advice for this flat applies to most homes on an HIU: have the HIU serviced once a year, around September. That way it is checked and running efficiently before the cold weather arrives, rather than being looked at for the first time when the heating fails in winter.

How to spot the same problem at home

If you live in a flat with underfloor heating and an HIU, here are some simple signs to look for (look only, don’t take anything apart):

  • Some or all rooms stay cold even though the thermostats are calling for heat.
  • The pressure gauge on the HIU reads low. Your HIU’s manual or label usually shows the normal range.
  • The flow meters on the manifold don’t move when the heating is on.
  • The heating has been off all summer and the first cold week shows a problem.

Low pressure that keeps coming back can point to a leak or another fault, so it is worth getting it checked properly rather than just topping it up again and again. If your flat is rented, tell your landlord or managing agent, as HIU repairs are often arranged by them or the building’s heat network operator. Our guides to HIU repairs and underfloor heating not working explain more.

Need an HIU or underfloor heating engineer in Loughton?

We repair and service HIUs and underfloor heating for homeowners, landlords and managing agents. See our HIU and CIU servicing and repair service, underfloor heating service and plumbing and heating service, or read about all our work in Loughton. Landlords can also book EICRs in Loughton from £175 + VAT.

Our office is in Chigwell, just down the road, and our engineers work across Essex every day, including Chigwell, Buckhurst Hill, Theydon Bois and Epping. Call 020 8227 0035 or request a quote.



Previous Post
Case Study: Consumer Unit Replacement in Tilbury, Essex
Next Post
Case Study: Ring Circuit Split and RCBO Upgrade in Wapping
Message us